Riello Oil Burner Pump 20030953 Replaces 3007811 & 3020475

£47.25
FREE Shipping

Riello Oil Burner Pump 20030953 Replaces 3007811 & 3020475

Riello Oil Burner Pump 20030953 Replaces 3007811 & 3020475

RRP: £94.50
Price: £47.25
£47.25 FREE Shipping

In stock

We accept the following payment methods

Description

This was replaced by RMG 508 SE GB control box; code 3001146. A direct plug in replacement, no wiring modifications required. Standard burners are only suitable for Hi/Lo operation on the oil side and fully modulating on the gas - but not fully modulating on both fuels. Newer 'Electronic Cam'burners may be fully modulating on both fuels. Please enquire for further details.

Photocell, faulty (or seeing light.) To test disconnect the photocell from the control box. Attempt a start sequence. If the burner lights (after 12 secs) and goes out, change photocell. Control box. If the above three items are satisfactory then consider the control box may be at fault (no tests are available for the control box.) Yes, it will cause the pump seals to leak. The RL series can be piped 2 pipe with both flexible oil lines fitted to a tee piece downstream of the filter and a single pipe from the oil tank. In conformity with Efficiency Directive 92/42/EEC the application of the burner on the boiler, adjustment and testing must be carried out observing the instruction manual of the boiler, including verification of the CO and CO 2 concentration in the flue gases, their temperatures and the average temperature of the water in the boiler. RL and RS 44 are available in 1 phase or 3 phase electrical supply (required phase must be specified.)If the pump is converted to single pipe with only one flexible oil line fitted the bypas screw MUST be removed. Having replaced my 3007450 pump with the replacement 3007811 pump, where do I fit the by-pass screw? Yesterday I had the burner out to see what was going on, it fired up when switching on and off for about eight times, after that, there was only a spark, no oil mist from the nozzle, it fired up once after this then no mist again. I left it for a few hours then when I switched it on I had a flame straight away but I'm not expecting it to last? This is replaced by the RMG 508 SE control box; code 3001138. A direct plug in replacement, no wiring modifications required.

My RL burner has been installed with a single pipe with the by-pass screw still in place. Will this effect the pump seals? This is replaced by the RMG 509 SE control box; code 3001139. A direct plug in replacement, no wiring modifications required.

Riello Control Box, 530E / SE RBS19

Yes, these are available for most of the larger burners, type and price can be obtained from our Sales Department. This was replaced by RMG 509 SE GB control box; code 3003383. A direct plug in replacement, no wiring modifications required.

No, all our burners require setting up by an engineer to suit the invidivual boiler it is attached to. Even if the correct size oil nozzle is fitted the burner will still require to be adjusted for the correct emmissions setting. NOTE:Unfortunately, Siemens are no longer producing these control boxes. As the affected burners are likely to be pre 1996 CE certification (20 or more years old!) Riello would recommend the complete replacement of the burner including the obsolescent control box to bring them in line with current standards.Hi two questions, that would be very helpful to have answered. Questions on how interchangeable oil pumps are. No, all gas valves are provided in the closed position so there is no tension on internal springs. All gas valves should require to be pre-set for adjusting for first firing.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop